Enum gimli::common::UnitSectionOffset

pub enum UnitSectionOffset<T = usize> {
    DebugInfoOffset(DebugInfoOffset<T>),
    DebugTypesOffset(DebugTypesOffset<T>),
}

An offset into the .debug_info or .debug_types sections.

Variants

DebugInfoOffset(DebugInfoOffset<T>)

An offset into the .debug_info section.

DebugTypesOffset(DebugTypesOffset<T>)

An offset into the .debug_types section.

Implementations

impl<T> UnitSectionOffset<T>

where T: Clone,

pub fn as_debug_info_offset(&self) -> Option<DebugInfoOffset<T>>

Returns the DebugInfoOffset inside, or None otherwise.

pub fn as_debug_types_offset(&self) -> Option<DebugTypesOffset<T>>

Returns the DebugTypesOffset inside, or None otherwise.

impl<T: ReaderOffset> UnitSectionOffset<T>

pub fn to_unit_offset<R>(&self, unit: &Unit<R>) -> Option<UnitOffset<T>>

where R: Reader<Offset = T>,

Convert an offset to be relative to the start of the given unit, instead of relative to the start of the section.

Returns None if the offset is not within the unit entries.

Trait Implementations

impl<T: Clone> Clone for UnitSectionOffset<T>

fn clone(&self) -> UnitSectionOffset<T>

Returns a copy of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl<T: Debug> Debug for UnitSectionOffset<T>

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl<T> From<DebugInfoOffset<T>> for UnitSectionOffset<T>

fn from(offset: DebugInfoOffset<T>) -> Self

Converts to this type from the input type.

impl<T> From<DebugTypesOffset<T>> for UnitSectionOffset<T>

fn from(offset: DebugTypesOffset<T>) -> Self

Converts to this type from the input type.

impl<T: Hash> Hash for UnitSectionOffset<T>

fn hash<__H: Hasher>(&self, state: &mut __H)

Feeds this value into the given Hasher.

fn hash_slice<H>(data: &[Self], state: &mut H)

where H: Hasher, Self: Sized,

Feeds a slice of this type into the given Hasher.

impl<T: Ord> Ord for UnitSectionOffset<T>

fn cmp(&self, other: &UnitSectionOffset<T>) -> Ordering

This method returns an Ordering between self and other.

fn max(self, other: Self) -> Self

where Self: Sized,

Compares and returns the maximum of two values.

fn min(self, other: Self) -> Self

where Self: Sized,

Compares and returns the minimum of two values.

fn clamp(self, min: Self, max: Self) -> Self

where Self: Sized + PartialOrd,

Restrict a value to a certain interval.

impl<T: PartialEq> PartialEq for UnitSectionOffset<T>

fn eq(&self, other: &UnitSectionOffset<T>) -> bool

This method tests for self and other values to be equal, and is used by ==.

fn ne(&self, other: &Rhs) -> bool

This method tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.

impl<T: PartialOrd> PartialOrd for UnitSectionOffset<T>

fn partial_cmp(&self, other: &UnitSectionOffset<T>) -> Option<Ordering>

This method returns an ordering between self and other values if one exists.

fn lt(&self, other: &Rhs) -> bool

This method tests less than (for self and other) and is used by the < operator.

fn le(&self, other: &Rhs) -> bool

This method tests less than or equal to (for self and other) and is used by the <= operator.

fn gt(&self, other: &Rhs) -> bool

This method tests greater than (for self and other) and is used by the > operator.

fn ge(&self, other: &Rhs) -> bool

This method tests greater than or equal to (for self and other) and is used by the >= operator.

impl<T: Copy> Copy for UnitSectionOffset<T>

impl<T: Eq> Eq for UnitSectionOffset<T>

impl<T> StructuralPartialEq for UnitSectionOffset<T>